Speaker configuration and “Amp Assign” settings

How to hook up a subwoofer to a stereo system Hint: You don’t necessarily need a receiver with subwoofer output jacks. Subs can provide a foundation to the sound that few speakers can muster on their own. So adding a sub is not just about adding more and deeper bass; rather, a properly integrated subwoofer can improve the overall sound of the system. AV receivers feature bass management to direct the low bass frequencies to the sub and the midrange and treble frequencies to the speakers. The subwoofer is hooked up to the receiver with a single interconnect cable. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options.

How to: Double your home theater receiver’s power

Share on Facebook The jobs of receivers and amplifiers overlap, as receivers are essentially tuners with amplifiers built-in. An audio-visual receiver can function as an audio distribution system, and as such, it functions as a jack-of-all-trades. A good-quality vintage stereo amp does one thing, and it performs better than the receiver when providing music and left and right front-channel audio. Adding an older power amplifier depends on your AV amplifier having audio pre-amp outputs for at least the left and right front channels.

This is available on many but not all AV amplifiers.

You’ll likely need a 4–6 foot analog audio cable with stereo RCA or miniplug jacks. If the TV and stereo system support HDMI connections, then be sure to pick up those cables as well. Once all the tools are available, hook up the speakers to the TV using the appropriate audio cables, and then power on .

How Do I Hook Up my subwoofer? Hook up Powered Subwoofers: Receiver Pre-Outs Before trying to hook up your subwoofer, you need to identify the connections it has. First, take a look at the back of your subwoofer. There may be more, but this is all you’ll need to properly connect your subwoofer. The last piece of prep work is for you to check your receiver. If you don’t have this output, you won’t be able to connect your sub this way.

Refer to Connecting a Non-Powered Subwoofer to get your subwoofer connected. Necessary Cables for Subwoofer and Pre-Out Connections You’ll need to obtain the following cables to complete your setup:

503 Service Temporarily Unavailable

Hi there, I am expanding my Sonos system. So far I am very extremely happy with Sonos. Before I went any further I wanted to find out what is the best way to hook up the Sonos Connect to my existing system so I can play the Sonos app music through my Home theater system. I am a bit confused as to what I need to do to get things setup correctly.

How to Hook up your Home Theater Receiver to Connect your Surround Sound If you’re new here, the way our How-To guides work is simple: First, you click a link, say, for Home Theater Receivers (which brought you here).

If so, can you let me know how? Are there any risks? It is time for me to summarize my most important conclusions at the amptone site. First you should read http: I’ve been re-reading wonderful books about recording the guitar and getting guitar sounds. See list at bottom. There are no risks for plugging a guitar into a home stereo, just look for these issues: If your guitar produces a quiet signal, there will be more background hiss than there should be.

I think I did this, perhaps from playing guitar directly into the stereo too aggressively without compression or distortion — it’s all one narrow frequency band, which, when clipping, can blow a tweeter of your high-fi speaker.

Sign Up & Save 10%

The most basic way to wire marine speakers to an amplifier is to connect one speaker to each of the available channels. But there are other options to consider. Most external amplifiers can power more than one speaker per channel. For example, a 4 channel amplifier may be able to power up to 8 speakers.

Solved Hook up rear inwall speakers directly to tv without receiver or amp Forum Trying to properly hook up an Onkyo A/V Receiver with a Samsung 65JS HDTV and am having difficulty trying to.

Share on Facebook Connecting a mixer to a receiver will expand input capabilities to include musical instruments, microphones and other sound-producing equipment. Requiring a stereo connection cable with plugs to fit both units, any receiver that contains auxiliary inputs — AV. Mixers are available in a variety of configurations and are used as a central connection point and volume control for external devices. Any nonpowered mixer can be connected to a stereo receiver.

Step Inspect the back of the receiver to ensure that auxiliary input jacks exist. The jacks will be labeled, are located near other input jacks for the tape or CD player and will be of the RCA variety. Any input may be used except the phono input reserved for turntables. Phono inputs employ a stronger signal preamp, which will cause distortion and poor sound when used with mixers and other devices.

Video of the Day Step Purchase a shielded stereo connection cable at a local electronics retailer or music store with two RCA plugs on one end and two plugs matching those of the mixer outputs on the other. Step Power off the mixer and receiver and ensure that all volume levels are down. Step Plug the cable’s dual RCA plugs into the receiver’s auxiliary left and right input jacks.

How to connect a headphones amp to a receiver?

How do you hook-up or wire up one light with two on-off switches? For information on how to hook-up one light with two on-off switches, see the Related link “How to wire 3-way and 4-way switches, including wiring diagrams”, shown below. When using the correct size wire, there are several possible configurations of power connection, lighting outlet, and the two 3-way switches. Power can come from the panel to one switch or the other, or to the light, whichever is convenient.

The light can be physically positioned between the switches or at the end of the two-switch series.

An audio-visual receiver can function as an audio distribution system, and as such, it functions as a jack-of-all-trades. A good-quality vintage stereo amp does one thing, and it performs better than the receiver when providing music and left and right front-channel audio.

Youse got a problem wit dat? Posts There’s no risk, per se. Originally Posted by nightflier Mark, Could you elaborate. I’m confused about the risks involved. My Arcam is a fairly pricey unit, so I want to be careful. Maybe I’m not understanding what the real difference is between the line outs, ie tape outs, and a preamp out which the Onkyo TX doesn’t have, by the way.

A Tape out passes the signal just after the phono pre-pre amp stage and selection stage. All of which add additional amplification to the signal. IOW, by using a “line out” between the preamp and the power amp you will be passing the output of your receiver’s preamp stage into the input of your new preamp. This would require you to adjust the volume control on both the receiver, the tone controls WILL have an effect on what’s passed to your amp, etc.

While it probably would not damage it, it may not sound as “pure” as you would like.

Spiacente!

Contact Us Improving Stereo Performance of a Surround Sound Setup — Part 1 I hear and read of numerous reports from people with surround sound systems, that are not performing as well as desired for stereo music playback. Some are people who sold their old stereo setup, jumped on the surround sound band wagon, and now miss the musical qualities of their previous system.

Others have started out with a surround sound system, but underestimated how much music they play and now find their system lacking in this department.

May 05,  · First, make sure your receiver has “pre-out” jacks on its rear panel (if yours doesn’t have one, you won’t be able to hook up a separate power amp like the XPA). Then it’s just a .

These mistakes can range from simple problematic issues to things that could quickly lead to premature device failure. Let me quickly explain why. Every cable has inherent resistance. The thinner the cable, the more resistance the cable will have. There are other factors as well, but this is the big one. The more resistance a cable has, the more it will affect the frequency response which is possible at the end of the cable run.

hook up subs without amp?

AK4SK on January 07, , Are antenna tuners always the last piece of gear before the feed line going to an antenna? In other words they are always downstream of any amplifier being used, correct? Why can’t a tuner be between the transceiver and amplifier? The primary purpose of your antenna tuner is to provide a lump sum impedance that matches the impedance of a transmitter to the impedance of a load to attain maximum power transfer between the two.

To accomplish that for a linear amplifier, it has to sit between the linear amplifier and the antenna.

To hook up a graphic equalizer to such a unit, remove the plugs and connect one pair of audio cables to the pre-amp output and the other end into the left and right channel inputs on the rear panel of the graphic equalizer.

I had almost forgotten what a simple pleasure it was to setup two speakers and just listen to music. No fancy DSP or bass management schemes. No APP to download. Just hookup a CD player or turntable and listen to the music. Bluetooth streaming is easy, convenient and sounded fine for everyday listening. Yamaha has taken a decent stereo receiver and made it eminently more useful and enjoyable.

Tutorial: AV Receivers and Amps Explained


Greetings! Do you need to find a partner for sex? Nothing is more simple! Click here, registration is free!